The MFI menu has 2 automatic trip memories: 1 – single trip memory and 2 – total trip memory. The number of the memory is shown at the upper right of the display. The trip memories are in addition to the trip odometer, which is displayed in the bottom part of the instrument cluster and controlled using the 0.0/SET button on the right of the instrument panel ⇒ Fig. 11⑦ ⇒ Fig. 12⑦ .
To display the distance driven on trips 1 and 2, select the Route item in the MFI menu (MFI > Route). Press the OK button (⇒ Fig. 16 ) to toggle between Route 1 and Route 2 (trip 1 and trip 2). Push and hold the OK button to manually reset a trip memory to zero.
1 | Single trip memory | The memory accumulates and stores information about
distance driven and fuel used from the time the ignition was switched on
until the time it was switched off. If the ignition stays off for 2 hours or more, stored information is automatically deleted. If the trip is continued within 2 hours after the ignition was switched off, the new values are added. |
2 | Total trip memory | The memory displays and stores the accumulated driving and fuel consumption data of any number of single trips up to a total driving time of 99 hours and 59 minutes, and up to a total distance of 9,999 miles (9,999 km), depending on the instrument cluster version. If one of the maximum values is exceeded, then the memory is automatically cleared and starts again from 0. |
Possible MFI menu displays
The following displays can be accessed in the MFI menu if enabled under Settings > MFI data. Displays that are not enabled will not appear.
Display | Function |
---|---|
Travel time | Driving time in hours (h) and minutes (min) corresponding to trip memories 1 and 2 (toggle). |
Consumption --- mpg | Current fuel consumption in miles per gallon (l/100 km) while driving. When units are set to miles, dashes appear instead of a number when the engine is running and the vehicle is standing still. When units are set to kilometers, the display shows liters consumed per hour when the engine is running and the vehicle is standing still. |
Avg. Consumption ø --- mpg | Average fuel consumption in miles per gallon (l/100 km) on trips per trip memories 1 and 2 (toggle) is displayed once the vehicle has been driven about 330 feet (100 m). Until then, dashes appear instead of a number. The value displayed is updated every 5 seconds. |
Range | Estimated distance in miles (km) that the vehicle can go with the fuel left in the tank the way you are currently driving. Takes account of the current fuel consumption, among other things. |
Route | Distance driven in miles (km) per trip memories 1 and 2 (toggle). |
Speed ø | Average speed on trips per trip memories 1 and 2 (toggle). Displayed once the vehicle has been once the vehicle has been driven about 300 feet (100 m). Until then, dashes appear instead of a number. The value displayed is updated every 5 seconds. |
0 speed | Digital display of current vehicle speed. |
Speed warn. --- mph (km/h) | When the set speed (from 20 to 155 mph - 30 to 250 km/h) is exceeded, an acoustic warning sounds, and a visual message may also appear in the instrument cluster display. |
Switching between the displays
Storing speed for the speed warning
Manually erasing trip memory 1 or 2
Enabling and disabling displays
Use the Settings menu, submenu MFI data (Settings > MFI data) to enable displays you want to be available under the MFI menu in the instrument cluster display. The units in which data is displayed can also be changed ⇒ Settings menu .
Volkswagen Tiguan Service and Repair Manual > Air Conditioning: Additional Components for Control and Regulation
Sunlight Photo Sensor -G107-, Removing and Installing
Special tools and workshop equipment required
Trim Removal Wedge -3409-
Vehicle Diagnostic Tester
Removing
Unclip the Sunlight Photo Sensor -G107--1-
from the instrument panel using the Trim Removal Wedge -3409-.
Remove the connector fro ...