VW Tiguan Manuals

Volkswagen Tiguan Service and Repair Manual: Wax Underbody Protection

Wax Underbody Protection -D 316 D38 A2-

Definition:

  • Wax Underbody Protection -D 316 D38 A2-

Product Description

Wax Underbody Protection -D 316 D38 A2- is an solvent-containing anti-corrosion agent based on wax and lanolin with polymer and rust-protection additives.

This results in a high viscosity and a relatively high abrasion resistance for wax.

The material seeps into the pores of the PVC coating, pushing out moisture and closing the pores to produce a waterproof, highly adhesive and firm coating.

After drying, it forms a light beige, transparent, non-sticking, waterproof film.

Its transparency enables the product to conform to German technical standards (TÜV)(the underbody can be monitored).

The dry film has good adhesion and corrosion protection properties and is very durable due to its toughness and resistancy.

Wax Underbody Protection -D 316 D38 A2- technical application information

Application

  • The material is primarily used on the underbody and especially for treatment and maintenance of all protective coats such as PVC, PVC/wax/bitumen/rubber/resin based materials.
  • It can also be used to treat chassis parts such as axles, wheel suspensions and springs. These parts become grey with age and are often the first to be affected by rust. The treatment refreshes the color which considerably improves the optical appearance. At the same time the parts are protected against corrosion.

Note

  • Before starting to apply, it is necessary to read the safety measures and advice in the safety data sheet.
  • Even for products which are not required to be labeled by law, the usual safety measures must be observed for chemical emissions.

Processing

  • Clean the surfaces to be treated with Wax Underbody Protection well beforehand and remove any rust.
  • The surfaces must be dry, free of grease, dirt and as much dust as possible.
  • The Wax Underbody Protection must only be applied to dry surfaces. Rust must be taken into account for older vehicles.
  • Rust should be removed with a wire brush.
  • Before work can start the vehicle should be covered, especially the door windows.
  • The Wax Underbody Protection can be applied to a vertical surfaces in one step. To prevent a spraying shadow, it is advisable to spray with cross coats.
  • After drying over night the vehicle can be used again. Between 24 and 48 hours are required for final drying.
  • An underbody protection spray gun is used when applying with the 1 L can. The can should be shaken before use.
  • Recommended wet film thickness 200 um, processing air pressure approximately 3 to 5 bar.
  • The Wax Underbody Protection can also be used with a pressure feed spray gun if the Venturi hooked probe (16139 SATA) is used. The application pressure is approximately 3 to 4 bar. A 750 mm flexible guide hose enables the operator to guide the hook with the 7 mm Venturi nozzle with ease.

Caution

Do not spray onto the steering, engine, driveshaft, exhaust, catalytic converter and brake systems.

Blow out the spraygun immediately after use and then rinse it with Plastic Cleaner -D 195 850 A1-.

If the spray gun becomes blocked the can may burst!

Observe the operating instructions of the UBS spray gun!

Cleaning
  • Splashes and spray mist on painted surfaces should be removed immediately using Plastic Cleaner -D 195 850 A1-. Material residue can also be cleaned off easily with mineral spirits or kerosene.
  • Larger surfaces can also be cleaned with a steam cleaner.
  • For this reason an underbody that has been treated with Wax Underbody Protection cannot be cleaned with steam cleaning devices unless it is to remove the old layer before new treatment can begin.

Technical Data

Color Transparent light beige
Odor Mild odor
Solid matter content approximately 47 %
Consistency Fluid, lightly thixotropic
Heat resistance of the dry film Greater than 100 ºC (212 ºF)
Complete drying 24 to 48 hours
Processing temperature +10 ºC to +25 ºC (50º to 77 ºF)
Application temperature -25 ºC to +80 ºC (-13º to 176 ºF) (short-term, up to one hour at +100 ºC (212 ºF) )

Wax Underbody Protection -D 316 000 A1-

Definition:

  • Wax Underbody Protection -D 316 000 A1-

Product Description

Wax Underbody Protection -D 316 000 A1- is an exceptional long-term corrosion protection.

The Wax Underbody Protection is based on a solvent-free, oxidative drying system and provides optimal corrosion protection for the body underbody area.

This long-term corrosion protection is established by its excellent adhesion at both very low and high temperatures to the metallic surface.

The product forms a light brown, elastic and non-tacky coating.

It is not necessary to combine the film at an elevated temperature.

Wax Underbody Protection -D 316 000 A1- technical application information

Application
  • The material is primarily used in the vehicle area.
  • Make sure that the base surfaces are dry.
  • The ready-made product is applied using brushes at the material temperature of +20 ºC (68 ºF) to 35 ºC (95 ºF).
  • The material can be carefully warmed up to 45 ºC (113 ºF) immediately before applying (< 5 minutes) if it is required by the application technique.
  • The oxidative hardening product can form a film on the surface after a short time. This has no impact on the corrosion protection or other properties.

Properties

  • Solvent-free
  • 100% active ingredient conten
  • Exceptional long-term corrosion protection
  • Good adhesion properties
  • Reduced tendency to drip
  • Low-temperature flexibility
  • Long shelf life

Note

  • Before starting to apply, it is necessary to read the safety measures and advice in the safety data sheet.
  • Even for products which are not required to be labeled by law, the usual safety measures must be observed for chemical emissions.

Processing

  • The surfaces that are to be treated must dry and be free of grease and dust.
  • Bring the Wax Underbody Protection to the application temperature of 20º to 35 ºC (68º to 95 ºF).
  • Apply the material to the body parts that are to be protected and spread using brushes.

Technical Data

Base Mixture of corrosion protection additives with a sulfonate base, alkyd, mineral oil aromatic extracts, pigments, thickening agents, drying agents and fluorescent pigments.
Delivery form/color Light brown, viscous fluid
Rheomat viscosity 1850 +- 350 mPas (System PP50, d= 760 1/s
Density/15 ºC DIN EN ISO 12185 0.995 +- 0.015 g/ml
Solid matter content 99 +- 1 %
Flashpoint DIN EN ISO 2719 approximately 150 ºC (302ºF)
Recommended layer thickness 100-400 um
Processing temperature 20º to 35 ºC (68º to 95 ºF)
Storage At temperatures of +10 ºC to +30 ºC (50 ºF to 86 ºF) for approximately 12 months
Container 310 ml

Wax Spray -D 322 100 M2-

Definition:

  • Wax Spray -D 322 100 M2-

Product Description

Wax Spray -D 322 100 M2- is a long-term anti-corrosion agent. After drying, the product forms a light brown, wax-like film. Because of its hardness, the Wax Spray provides good protection against mechanical stress.

Wax Spray -D 322 100 M2- technical application information

Application

  • The material is primarily used in the vehicle area, but it is also used as temporary corrosion protection for tools and machines.
  • The Wax Spray does not corrode vehicle paint and adheres to almost all base surfaces.

Note

  • Before starting to apply, it is necessary to read the safety measures and advice in the safety data sheet.
  • Even for products which are not required to be labeled by law, the usual safety measures must be observed for chemical emissions.

Processing

  • Bring the Wax Spray to room temperature (16º to 20 ºC (60.8º to 68 ºF).
  • Briefly shake the spray can before using.
  • The surfaces that are to be treated (underbodies, wheel housings, insides of door) must dry and be free of grease and dust.
  • The Wax Spray is sprayed on evenly in cross coats at a distance of 20 to 30 cm.

Caution

Do not spray onto the steering, engine, driveshaft, exhaust, catalytic converter and brake systems.

Technical Data

Base Wax mixture
Color Light brown/transparent
Film type Hard and wax-like
Density 0.735 g/cm³
Solids content 35.4 %
Flashpoint/Active agent 29 ºC (84.2ºF)
Flashpoint/Spray < -20
Recommended layer thickness 50 um/wet
Drying time approximately 30 minutes
Heat stability 105 ºC (221 ºF)
Removability Mineral spirits
Processing temperature 16 to 20 ºC (60.8 to 68 ºF)
Propellant gas (Aerosol) Propane / Butane
Aerosol storage Cool and dry, < 50 ºC (122 ºF)
Hazard warning Highly flammable
Container 500 ml
    Stone Chip Protection
    Stone Chip Protection -AKR 311 KD1 05- Definition: Stone Chip Protection -AKR 311 KD1 05-, black Product DescriptionStone Chip Protection -AKR 311 KD1 05- is a finely atomizing coating material wi ...

    Sealing Materials
    Polyurethane Adhesive Sealant Definition: Polyurethane Adhesive Sealant -AKD 476 KD5 05- Product Description Polyurethane Adhesive Sealant -AKD 476 KD5 05- is a paste-like, one-part adhesive seali ...

    See More:

    Volkswagen Tiguan Owners Manual > Changing light bulbs: Changing the light bulb in the backup lamp
    Read and follow the introductory information and safety information first⇒Introduction to the subject The light bulbs for the backup lights are Lifetime bulbs with a very long service life. If the bulb is defective, you cannot change it yourself because other vehicle components must be r ...

    Volkswagen Tiguan Owners Manual

    Volkswagen Tiguan Service and Repair Manual

    © 2018-2021 Copyright www.vwtiguan.org - 0.0173